Contents [hide] 1 Coding 2 Adaptation 3 Basic Setting 3.1 Throttle Body 3.2 Kick Down 3.3 Fuel Pump 3.4 Intake Manifold Runner 3.5 Readiness 4 Special Functions 4.1 Checking Fuel Pressure Coding Byte 00 Manufacturer 01 Audi 02 Skoda 03 Seat 04 Volkswagen Byte 01 Model 03 Audi A3 (8P) / Seat Altea/Toledo (5P) / Seat Leon (1P) / Skoda Octavia (1Z) / VW Golf (1K) 04 Audi A4 Limousine (8EC) / VW Passat (3C) 05 Audi A6 Limousine (4F2) 0C Audi A4 Avant (8ED) 0D Audi A6 Avant (4F5) 13 Audi TT Coupé (8J) 14 Audi A5 Coupé (8T) 1C Audi A4 Cabriolet (8H) / VW Eos (1F7) 23 VW Tiguan (5N) Byte 02 Market 00 Europe / Rest of World (RoW) 01 North America 02 Russia (GUS) / China 04 South Africa 08 Mexico / Taiwan / Korea Byte 03 Emissions 00 EU-II 03 EU-IV 06 USA LEV 0A USA ULEV II Byte 04 Transmission 02 Automatic Transmission "multitronic" (01J) 18 6-Speed Manual Transmission 19 Automatic Transmission (09L) 1C 6-Speed Direct Shift Gearbox (DSG/02E) Byte 05 Special Functions I 03 Front-Wheel-Drive (FWD) / Climate Control not equipped 07 Front-Wheel-Drive (FWD) / Climate Control equipped 0C All-Wheel-Drive (AWD) / Climate Control not equipped 0F All-Wheel-Drive (AWD) / Climate Control equipped Byte 06 Special Functions II Bit 0 Cruise Control installed Bit 1 Adaptive Cruise Control (ACC) installed Bit 2 Suspension Levelling installed Bit 3 Trailer installed Byte 07 Cooling 18 1 Cooling Fan 20 2 Cooling Fans 60 2 Cooling Fans + Additional Water Pump Adaptation Basic Setting Throttle Body Prerequisites: Ignition ON Engine OFF System voltage at least 11.0 V. [Select] [01 - Engine] [Basic Settings - 04] Group 060 [Go!] Activate the Basic Setting. [ON/OFF/Next] Wait until Field 4 shows "ADP. O.K.". [Done, Go Back] [Close Controller, Go Back - 06] Switch Ignition OFF. Kick Down Prerequisites: Ignition ON Engine OFF System voltage at least 11.0 V. [Select] [01 - Engine] [Basic Settings - 04] Group 063 [Go!] Activate the Basic Setting. [ON/OFF/Next] Press the pedal to the floor and hold it there for at least 2 seconds. Observe Field 4, once the adaptation is successfully done it should show "ADP. O.K.". [Done, Go Back] [Close Controller, Go Back - 06] Switch Ignition OFF. Fuel Pump Prerequisites: Ignition ON Engine ON System voltage at least 11.0 V. [Select] [01 - Engine] [Basic Settings - 04] Group 103 [Go!] Activate the Basic Setting. [ON/OFF/Next] Wait until Field 4 shows "ADP. O.K.". [Done, Go Back] [Close Controller, Go Back - 06] Switch Ignition OFF. Intake Manifold Runner Prerequisites: Ignition ON Engine OFF System voltage at least 11.0 V. [Select] [01 - Engine] [Basic Settings - 04] Group 142 [Go!] Activate the Basic Setting. [ON/OFF/Next] Wait until Field 4 shows "ADP. O.K.". [Done, Go Back] [Close Controller, Go Back - 06] Switch Ignition OFF for at least 60 seconds. Notes: The newer timing chain driven engines which were phased in during model year 2009 the engine may need to be running at idle. Common examples of these engine codes include CCTA, CBFA and CCTA. Never run Basic Settings with the IMRC motor linkage disconnected from the intake manifold. It may damage the new part. Readiness Prerequisites: Ignition ON Engine at idle No fault codes [Select] [01 - Engine] [Basic Settings - 04] Group 200 [Go!] Activate the Basic Setting. [ON/OFF/Next] Firmly press Brake Pedal and Throttle Pedal (Full Throttle) at once to activate the basic setting. Field 1 shows the steps counter, which counts down to 0 - then setting readiness is done. Stay on the pedals as long as the procedure lasts. [Done, Go Back] [Close Controller, Go Back - 06] Special Functions Checking Fuel Pressure Prerequisites: Ignition ON Engine ON (Idle) System voltage at least 11.0 V. Coolant Temperature at least 80 °C [Select] [01 - Engine] [Meas. Blocks - 08] Group 103 [Go!] Field 1: Fuel Pressure (Low), Specification: 2800...7200 mbar Field 2: Fuel Pump Adaptation, Specification: -1000...+1000 % Group 140 [Go!] Field 3: Fuel Rail Pressure (High), Specification: 25.0...110.0 bar Increase the Engine Speed while checking this value, the Pressure has to rise with the Engine Speed. Group 230 [Go!] Field 1: Specified Fuel Rail Pressure (High) Field 2: Actual Fuel Rail Pressure (High), Specification: 25.0...110.0 bar Field 3: Deviation between specified and actual fuel pressure, Specification: max. 5.0 bar [Done, Go Back] [Close Controller, Go Back - 06] Categories: EnginesGasoline Engines Categories Main Page Diagnostic Procedures Common Procedures Fault Codes Retrofitting Immobilizer Meta Log in Unless otherwise noted, all content on this site is Copyright © 2000-2010 by Ross-Tech LLC. All rights reserved. "VCDS" is a Registered Trademark of Ross-Tech, LLC. Ross-Tech is not affiliated with the Volkswagen Group in any way.
Posted on: Fri, 02 Aug 2013 17:30:45 +0000
Recently Viewed Topics
© 2015