Types of Single Phase AC Induction Motors Split-Phase AC Induction Motor (See Fig.1) The split-phase motor is also known as an induction start/induction run motor. It has two windings: a start and a main winding. The start winding is made with smaller gauge wire and fewer turns, relative to the main winding to create more resistance, thus putting the start winding’s field at a different angle than that of the main winding which causes the motor to start rotating. The main winding, which is of a heavier wire, keeps the motor running the rest of the time. The starting torque is low, typically 100% to 175% of the rated torque. The motor draws high starting current, approximately 700% to 1,000% of the rated current. The maximum generated torque ranges from 250% to 350% of the rated torque (see Figure 9 for torque-speed curve). Good applications for split- phase motors include small grinders, small fans and blowers and other low starting torque applications with power needs from 1/20 to 1/3 hp. Avoid using this type of motor in any applications requiring high on/off cycle rates or high torque. Capacitor Start AC Induction Motor (See Fig.2) This is a modified split-phase motor with a capacitor in series with the start winding to provide a start “boost.” Like the split-phase motor, the capacitor start motor also has a centrifugal switch which disconnects the start winding and the capacitor when the motor reaches about 75% of the rated speed. Since the capacitor is in series with the start circuit, it creates more starting torque, typically 200% to 400% of the rated torque. And the starting current, usually 450% to 575% of the rated current, is much lower than the split-phase due to the larger wire in the start circuit. Refer to Figure 9 for torque-speed curve. A modified version of the capacitor start motor is the resistance start motor. In this motor type, the starting capacitor is replaced by a resistor. The resistance start motor is used in applications where the starting torque requirement is less than that provided by the capacitor start motor. They are used in a wide range of belt-drive applications like small conveyors, large blowers and pumps, as well as many direct-drive or geared applications. Permanent Split Capacitor (Capacitor Run) AC Induction Motor (See Fig.3) A permanent split capacitor (PSC) motor has a run type capacitor permanently connected in series with the start winding. This makes the start winding an auxiliary winding once the motor reaches the running speed. Since the run capacitor must be designed for continuous use, it cannot provide the starting boost of a starting capacitor. The typical starting torque of the PSC motor is low, from 30% to 150% of the rated torque. PSC motors have low starting current, usually less than 200% of the rated current, making them excellent for applications with high on/off cycle rates. Refer to Figure 9 for torque- speed curve. The PSC motors have several advantages. The motor design can easily be altered for use with speed controllers. They can also be designed for optimum efficiency and High-Power Factor (PF) at the rated load. They’re considered to be the most reliable of the single-phase motors, mainly because no centrifugal starting switch is required. Permanent split-capacitor motors have a wide variety of applications depending on the design. These include fans, blowers with low starting torque needs and intermittent cycling uses, such as adjusting mechanisms, gate operators and garage door openers. Capacitor Start/Capacitor Run AC Induction Motor (See Fig.4) This motor has a start type capacitor in series with the auxiliary winding like the capacitor start motor for high starting torque. Like a PSC motor, it also has a run type capacitor that is in series with the auxiliary winding after the start capacitor is switched out of the circuit. This allows high overload torque. This type of motor can be designed for lower full-load currents and higher efficiency (see Figure 9 for torquespeed curve). This motor is costly due to start and run capacitors and centrifugal switch. It is able to handle applications too demanding for any other kind of single-phase motor. These include woodworking machinery, air compressors, high- pressure water pumps, vacuum pumps and other high torque applications requiring 1 to 10 hp. Shaded-Pole AC Induction Motor (See Fig.5) Shaded-pole motors have only one main winding and no start winding. Starting is by means of a design that rings a continuous copper loop around a small portion of each of the motor poles. This “shades” that portion of the pole, causing the magnetic field in the shaded area to lag behind the field in the unshaded area. The reaction of the two fields gets the shaft rotating. Because the shaded-pole motor lacks a start winding, starting switch or capacitor, it is electrically simple and inexpensive. Also, the speed can be controlled merely by varying voltage, or through a multi-tap winding. Mechanically, the shaded-pole motor construction allows high-volume production. In fact, these are usually considered as “disposable” motors, meaning they are much cheaper to replace than to repair. The shaded- pole motor has many positive features but it also has several disadvantages. It’s low starting torque is typically 25% to 75% of the rated torque. It is a high slip motor with a running speed 7% to 10% below the synchronous speed. Generally, efficiency of this motor type is very low (below 20%). The low initial cost suits the shaded-pole motors to low horsepower or light duty applications. Perhaps their largest use is in multi- speed fans for household use. But the low torque, low efficiency and less sturdy mechanical features make shaded-pole motors impractical for most industrial or commercial use, where higher cycle rates or continuous duty are the norm. Figure 9 shows the torque-speed curves of various kinds of single-phase AC induction motors.
Posted on: Wed, 19 Mar 2014 08:50:38 +0000
Trending Topics
Recently Viewed Topics
© 2015