90304 Classic Turret Press Kit This kit and a set of Lee dies is everything you need to begin reloading. The Classic turret press is fast and convenient when loading handgun cartridges, with rates in excess of 250 rounds per hour possible. The kit includes the Pro Auto-Disk powder measure and riser, perfect for all handgun and small rifle cartridges. Large and Small Safety Prime are included making on press priming an ease. Instant change turret makes changing calibers a snap. Deactivate the auto-index and batch load the longest and largest rifle cartridges. Complementing your press kit are the case conditioning tools to prepare your brass for loading. Includes Cutter, Lock Stud, Chamfer Tool, small and large Primer Pocket Cleaner, and a tube of Lee case sizing lube. Complete it with the cartridge specific Case Length Gauge. Verify your loads with the included Lee Safety powder scale. Completing the kit is Modern Reloading Second Edition recently revised with all new load data covering 167 cartridges with over 28,000 loads. 90792 Adjustable Charge Bar Lee Adjustable Charge Bar is used in place of the Charge Disk on the Auto Disk and Pro Auto Disk Powder Measures. Adjustable between .28 cc and 1.6 cc QTY 3 90269 Turrets Lee Aluminum 4-hole Turret for quick caliber change for the 4-Hole Turret Press and Classic Turret Press. This 4 hole turret will not fit inside the Pro 1000 or 3 Hole Turret Press. 90195 Double Disk Kit Lee Double Disk Kit raises powder hopper permitting two disks to be stacked in powder measure. Doubles the capacity, also able to make very fine adjustments. Disk A = .30 to .43 cc Disk B = .46 to .66 cc Disk C = .71 to 1.02 cc Disk D = 1.09 to 1.57 cc 90194 Rifle Charging Die Lee Rifle Charging Die charges small capacity rifle cases when used with the Auto Disk Powder Measure or Pro Auto Disk Powder Measure. It works the same as the pistol powder through expanding die, except it doesn`t expand the case mouth. Rifle case expansion is done in the sizing die. Can be used on 22 cal. cartridges and up to and including the .308 Win. 90041 Auto Disk Riser Lee Auto Disk Riser raises the Auto Disk powder measure higher above the mounting location on the Turret Press to provide clearance for use of the Safety Prime 90507 308 Winchester PaceSetter Dies Lee 308 Pacesetter 3-Die Set includes Full Length Sizing Die, Easy Adjust Dead Length Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. 90508 30/06 Springfield PaceSetter Dies Lee 30/06 Pacesetter 3-Die Set includes Full Length Sizing Die, Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data 90731 7.62x54R PaceSetter Dies Lee 7.62X54 Russian Pacesetter 3-Die Set includes Full Length Sizing Die, Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. This die set includes a .308 expander. The 7.62 x 54 Russian load data has been developed around the .308 diameter. If your rifle has a .311 groove dimension, order the .311 expander here: /EZ-X-EXP-303-B.html PaceSetter 3-Die Set includes the exclusive Lee Factory Crimp Die Lee PaceSetter Dies include the exclusive Lee Factory Crimp Die to produce factory-like ammunition with improved utility and accuracy. The die set also includes a conventional bullet seater. They also include a shell holder, powder dipper, load data and are packed in the nicest storage box ever designed. These extras represent an $18.00 value. Most are unavailable at any price from other suppliers. These are the most copied dies in the world. Each and every die comes with a written lifetime warranty, 2-year guarantee and guaranteed of accuracy or your money back. All Lee dies are machine honed to the smoothest possible finish. Dont confuse this with the surface polish used by most manufacturers. A polish simply makes a shiny surface. Its like trying to sand wood without backing under the sandpaper. The surface in Lee dies is progressively honed to a fine finish with no waves or ripples. 90625 380AUTO Carbide Handgun Dies Lee 380 Pistol 3-Die Set includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. 90867 380AUTO Carbide Factory Crimp Die Lee 380 Auto Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders. 90799 40S&W Carbide Handgun Dies Lee 40 S&W Pistol 3-Die Set includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. Can be used to load the 10mm Auto. Back out the bullet seating die and powder through expanding die 1 3/4 turns. 10mm Load Data is found in Modern Reloading or available for purchase here. 90862 40S&W Carbide Factory Crimp Die Lee 40 S&W/10MM Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders. 90155 Case Length Gauge/Trimmer 380Auto Lee 380 AUTO Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim 90154 Case Length Gauge/Trimmer 40 S&W Lee 40 S&W Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim 90139 Case Length Gauge/Trimmer 308 Winchester Lee 308 WIN Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim 90147 Case Length Gauge/Trimmer 7.62x54R Lee 7.62X54 RUSSIAN Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim 90140 Case Length Gauge/Trimmer 30/06 Springfield Lee 30/06 SPRINGFIELD Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim 90688 Reloading Stand 90011 Load-ALL II 12G Shotshell Reloading Press LEE LOAD-ALL II shotgun shells not only look better than those loaded on machines costing hundreds of dollars, but they usually have more uniform velocity and patterns. You can load just as fast as with any other brand of loader costing up to $200. Twenty-four shot and powder bushings are included free. The bushings alone can cost several dollars each from other manufacturers - and theyre not as accurate as those made by Lee. Only Lee supplies molded bushings. This is a time proven tool. There are hundreds of thousands in use world-wide. In over forty years, we have yet to see one worn out. Includes OPTIONAL AUTO PRIMER Features: Capable of reloading 200 shells per hour Hopper holds over 5 lbs. of shot, enough to load over 125 rounds Built-in primer catcher with an easy-to-empty door right up front Recesses at every station for speedy shell positioning Easy and economical gauge conversion Optional primer feeder so you never need to touch the primer from the box to the shell Adjustable from the standard 2 3/4 shell, up to 3 inch shell
Posted on: Tue, 14 Oct 2014 11:24:35 +0000
Trending Topics
Recently Viewed Topics
© 2015