2000+ rescue school of music future 1946 Fender founded by Clarence Leonidas “Leo” Fender 1954 Stratocaster ® unveiled 1960 Jazz Bass ® created 1965 Fender sold to CBS 1951 Precision Bass ® and Bassman ® amp created 1952 The Twin Amp ® created 1950 Telecaster ® and Esquire ® created 1958 Jazzmaster ® quitar created mid-1980s modern-era Fender launched 1962 Jaguar ® quitar created Timeline 5 History 6 strap button body pickups pickup pole piece intonation adjustment screw bridge saddle bridge output jack volume/tone control knobs pickguard string strap button truss rod adjustment (depending on model) neck Whether you know the names of all the parts or not, anatomical charts are always cool. Here’s the basic anatomy of a bass guitar: Anatomy 101 7 Anatomy Figure I Figure J Figure K String Height (Action) Adjustment The factory specification for string height for Fender® bass guitars is 6/64” on both the bass and treble sides. Before beginning, make sure your bass is tuned to proper pitch to facilitate an accurate measurement. Then, using your ruler, measure the distance between the bottom of each string and the top of the 17th fret, ( Figure I ) . Adjust the bridge saddles to height according to the the factory recommendation, then re-tune. Use a mini-standard screwdriver for vintage saddles, ( Figure J ) . Use the supplied hex wrench for modern saddles, ( Figure K ) . Don’t be afraid to experiment with the height a little bit, until it feels right to you. If you play with a light touch you can get away with lower action. If you play hard, you’ll need a little higher action to avoid fret buzz and rattles. 19 Set-up Figure L Figure M Shimming and Micro-Tilt ™ Adjustment Shimming is a procedure used to adjust the pitch, or angle of the neck in relation to the body and may be accomplished with either the use of a shim or by performing a Micro-Tilt adjustment. The need to adjust the pitch may occur when the relative string height is high, but the action adjustment is already as low as the string height adjustment will allow . A shim or a Micro-Tilt adjustment will tilt the neck back, relative to the plane of the body, which allows an increased range of action adjustment. The Micro-Tilt adjustment is a feature on some Fender ® basses, that performs the same function as shimming, by tightening a hex screw in the neck pocket of the body against a pressure plate installed in the bottom of the neck. The Micro-Tilt eliminates the need to remove the neck from the body to perform the adjustment. For those basses with the Micro-Tilt adjustment and a 3-bolt neck plate, first loosen the two neck mounting screws at the top, 1/2 turn. Next, loosen the neck mounting screw nearest to the adjustment access hole on the neckplate by at least 4 full turns, ( Figure L ) . Then, tighten the hex screw through the hole in the neck plate with a 1/8” hex wrench approximately 1/4 turn, ( Figure M ) . Retighten the neck screws when the adjustment is complete. 20 Set-up Figure N Figure O To shim the neck, you must first remove the strings. Next, remove the four screws that hold the neck in place then separate the neck from the body, ( Figure N ) . Note: All finishes remain somewhat elastic. Use care in separating the neck from the body as damage to the finish may occur if the neck finish has adhered to the body finish. Inadvertent damage caused to an instrument during set-up or adjustment is the responsibility of the consumer and will not be covered under the Fender ® warranty. Place a shim approximately 1/4” wide x 1 3/4” long x .010” thick, (the thickness of a standard business card) at the end of the neck pocket, ( Figure O ), and re-attach the neck. Placing the shim in the neck pocket will ef fectively lower the string action, and allow approximately 1/32” of additional saddle height travel. Note: If you feel you need to make a pitch adjustment and you’re not comfortable with the procedure, take your bass to an authorized Fender Service Center. 21 Set-up Figure Q Figure P Pickup Height Adjustment Properly adjusted pickups will ensure that your bass is performing to the best of its capability . On the other hand, improper pickup height can be the source of a couple of potentially confusing problems. Pickups set too low will appear to have a loss of output. Pickups set too high can cause excessive magnetic string pull, which may result in pitch warbling or false sharp readings when intonating your instrument. The pickups on your new bass are height adjustable for locating them in the appropriate relative position to the strings for optimum performance. To measure pickup height, depress each of the outside strings at the last fret. Using your ruler, measure the distances from the bottom of the strings to the top of the corresponding pole pieces on the pickups, ( Figure P ) . For pickups without pole pieces, or those having flush mounted pole pieces, measure to the pickup surface. Use the Pickup Height Adjustment Chart as a starting point. The actual height you adjust to may vary, depending on the amount of magnetic pull of the pickup and the type of strings you are using. Heavier gauges of strings generally produce a higher amplitude of vibration and may require a bit more clearance. Adjust pickup height with a small Phillips screwdriver, ( Figure Q ) . Note: When adjusting a pickup higher, it may be necessary to physically pull the pickup up into its raised position, as the foam spacer under the pickup typically compresses over time and will need the lift to help it expand and fill the void. 22 Set-up Pickup Height Adjustment Chart Pickup Type Bass Side Treble Side Vintage Style Precision Bass ® 8/64” 6/64” Vintage Style Jazz Bass ® 8/64” 6/64” Standard Jazz Bass 7/64” 5/64” Standard Precision Bass 7/64” 5/64” American Standard Jazz Bass 7/64” 5/64” American Standard Precision Bass 7/64” 5/64” Vintage Noiseless™ Jazz Bass 8/64” 6/64” N3 Noiseless Jazz Bass 8/64” 6/64” Special Design Humbucking 7/64” 5/64” 23 Set-up Modern Bridge Figure R Vintage Style Bridge Figure S Intonation Adjustment Note: Adjust the intonation only after completing all of the “Setup” steps on the previous pages. To intonate the bass we either shorten or lengthen the active vibrating length of each string so that it will be in tune with itself, relative to the scale length of the instrument. Intonation may be affected by climatic conditions, changes in neck relief, dirty, worn strings and even the process of putting on brand new strings, so it’s a good idea to make checking and adjusting intonation a regular part of your maintenance routine. To set the intonation for your bass you will need an electronic tuner and either a small Phillips or standard screwdriver or hex wrench, (depending on whether the saddle length adjustment screws on your bridge are either Phillips, standard or hex). Note: A bass that has not been properly intonated will not play in tune, up and down the neck, even if you have tuned each string to accurate pitch with an electronic tuner . 24 Set-up The procedure for setting your intonation is as follows: 1. Plug into your tuner and turn the volume full up on the bass. Strike the harmonic, ( see Tuning, page 13 ), at the 12th fret,and tune the string to the appropriate pitch. 2. Lightly press the string to the 12th fret, and recheck the pitch on the tuner . (If you press too heavily it will result in a false sharp reading.) 3. If the pitch of the harmonic and the pitch of the fretted note agree, then the string is properly intonated, and no adjustment will be necessary. If the two pitches disagree, you’ll need to make on of the following adjustments, using either a Phillips screwdriver or a hex wrench, depending on your specific bridge. 4. If the fretted note is sharper (higher in pitch relative to the harmonic), you will need to lengthen the active vibrating length of the string until the two pitches agree. To do this, turn the saddle length adjustment screw clockwise, moving the saddle toward the back of the bridge, until the harmonic and the fretted note register as the same pitch, ( Figure R ) . It’s a good idea to stretch and re-tune the string during the adjustment, as the movement of the saddle will affect the pitch. 5. If the fretted note is flatter, (lower in pitch relative to the harmonic), you will need to shorten the active vibrating length of the string until the pitches agree. To do this, turn the saddle length adjustment screw counter-clockwise, moving the saddle forward, until the harmonic and the fretted note register as the same pitch, ( Figure S ). Remember to stretch and re-tune the string. Note: You may need to de-tune slightly and manually push the saddle forward to complete the adjustment, as the downward pressure from the string may not allow the saddle to move forward freely. 6. When these procedures have been completed on each string, your bass should be properly intonated. Perform a final tuning check and there’s only one thing left to do. Just plug into your amp and Make History™! 25 Set-up CARE AND MAINTENANCE Your new Fender ® bass is precision crafted to give you many years of playing satisfaction. A few simple maintenance procedures will help keep your instrument in top condition for years to come. Keep Your Bass Clean: Dirt, dust, skin oils, perspiration and smoke can prematurely age the finish and fittings of your bass. Wipe down the entire instrument with a soft dry Fender approved polish cloth after each use. Clean and polish your bass periodically using a Fender approved polish on the finished wood surfaces and Fender approved polish/cleaner on the metal surfaces, then dry with a soft polishing cloth. Visit fender for information on Fender approved polish and polishing cloths. Oil The Fretboard Periodically: The natural oils in Rosewood, Pau Ferro and Ebony fingerboards may dry out over time. Rough, exposed fret edges are evidence of dry, shrunken wood. It is a good idea to give your fretboard a “drink” of lemon oil, boiled linseed oil or other non silicone-based wood/furniture oil, periodically to preserve its integrity and natural beauty. Note: With the strings removed, apply oil first to a clean lint free cloth, rub into the wood, let it soak in for a few minutes, and then wipe to dry any excess oil. Do not apply oil to the finished surfaces of the bass. Examine Strap Buttons Periodically: Over time, the shifting weight of your bass on the strap may cause the strap button screws to loosen up. Snug them up from time to time. If loose screws are neglected and not tightened up, the moving weight of the instrument may expand the mounting holes to the point where the screws will no longer hold fast. Setup And Adjust As Needed: Familiarize yourself with the setup and adjustment procedures in this manual or visit an Authorized Fender Service Center and adjust as needed. Note: Neglecting an instrument that is in need of adjustment may lead to complications. Seasonal Adjustments: Your bass, like all instruments made from wood, can be sensitive to seasonal fluctuations of temperature and humidity. It is natural for the woods to expand and contract with these changes and this movement can affect the setup and playability of the bass. It’s a good idea to schedule routine adjustments to compensate for the effects of these seasonal variations. 26 Care Avoid Exposing Your Bass To Climatic Extremes: Extremes in temperature and humidity may damage the instrument. If exposure is unavoidable, as during shipping, reduce string tension slightly to minimize potential damage. Allow a cold instrument to warm gradually before opening its case to avoid finish checking. Never leave your bass for any length of time, in an environment that you wouldn’t feel comfortable in yourself. Lacquer Finishes: Many Fender basses are finished with lacquer, a thin natural type of wood finish that has been used on fine handcrafted furniture and elite musical instruments for many years. Lacquer was the finish of choice for the most collectable and desirable vintage Fender instruments made in the ‘50s and ‘60s. Lacquer is a relatively thin and somewhat porous finish that allows the tone-woods to resonate much more freely , resulting in a more vibrant, and to many seasoned players, beautiful sounding instrument. While lacquer allows the instrument to vibrate generously, by its very nature, it is much more subject to the effects of wear, the aging of the underlying wood, chemical interactions and climatic conditions, than urethane or polyester finishes. If your bass is finished with lacquer, please make sure that you read the “Lacquer Finishes: Precautions and Care” card that accompanies your instrument. Avoid exposure of lacquer finishes to dyed fabrics or leathers, plastics, synthetics and surgical rubber tubing, (used on many guitar stands, hangers and straps), these materials will react adversely with the lacquer and mar the finish of the instrument. If you are unsure of what type of finish is used on your bass, please check the detailed specifications of your instrument at fender or call our Consumer Relations department at: 480-596-7195. Note: Checking, shrinkage, sinking, discoloration and rapid wear are all a natural part of the aging process of lacquer finishes, and as such, will not be covered under the Fender ® warranty. 27 Care SERVICE: For service in the United States and Canada, please contact an Authorized Fender Service Center, which you can find by calling the Fender Consumer Relations Department (480.596.7195) or using the “Service Center Finder” link on the “Support” section of fender . For service outside the United States and Canada, please contact your authorized dealer or the Fender distributor in your country or region—there’s a helpful global “International Distributors” link on the “Resources” section of fender . 28 Service Fender Musical Instruments Corporation warrants this Fender brand instrument to be free from defects in materials and workmanship for as long as it is owned by the original retail purchaser, except that pickups, switches, jacks, controls, all other electronic components, tuning machines, hardware, pickguards, plated surfaces, gig bags, cases and case hardware are warranted for a period of one (1) year from the date of original purchase. This warranty applies only to the original retail purchaser when this instrument is purchased from an Authorized Fender Dealer and is subject to the limitations set forth herein. IMPORTANT: PLEASE RETAIN YOUR ORIGINAL SALES RECEIPT, AS IT IS YOUR PROOF OF PURCHASE VALIDATING THIS LIMITED WARRANTY. Fender has established a network of independent Authorized Fender Service Centers for warranty service. The Fender Dealer from whom you purchased your instrument may also be authorized for warranty service and should be the first point of contact when service of any kind is required for your Fender instrument. To receive warranty service, return the complete instrument to an Authorized Fender Service Center, with your sales receipt as proof of purchase, during the applicable warranty period. Defective components that qualify for coverage under this warranty will be repaired or replaced (at Fender ’s discretion) without charge. Remedies beyond normal service repair of any Fender instrument require both an evaluation and confirmation of the defect and a direct recommendation to Fender from an Authorized Fender Service Center for alternative considerations. Fender Electric Instrument Limited Lifetime Warranty 29 Warranty All transportation, insurance and freight charges associated with warranty service and repairs on Fender instruments are the responsibility of the purchaser, as is any service initiated for the purpose of customizing setups or adjustments beyond factory specifications. Initial standard setup and adjustment of the instrument and its components at the time of purchase are considered normal Dealer product preparation and are not covered by this warranty. Limitations and exclusions The following items are not covered by this warranty. 1. Fret wear, saddle wear, nut wear, strings and batteries. 2. Checking, shrinking, sinking, discoloration and wear of lacquer finishes. 3. Setups, adjustments or routine maintenance of any kind. 4. Damage to finishes or cracks, splitting, or warpage of wood due to changes in temperature or humidity , exposure to or contact with sun, fire, moisture, body salts and acids of perspiration, guitar straps, guitar stands/hangers made from vinyl, plastic, rubber or other synthetic materials, any other chemicals or non-Fender-approved polishes. 5. Damage, corrosion or rusting of any hardware components caused by humidity, salty air, or exposure to the moisture, body salts and acids of perspiration. 30 Warranty 6. Any damage to an instrument resulting from customization or modification. 7. Normal wear and tear on any part of the instrument case or gig bag including jacks, controls, switches, plated surfaces, tuning machines, pickguards, zippers, clasps, handles, latches, case hardware, etc. 8. All other damage and deterioration due to normal usage, wear and tear , aging, accidents, neglect, abuse, or Acts of Nature. 9. Any instrument, whose serial number is missing, altered or tampered with in any fashion. 10. Any instrument purchased from anyone other than an Authorized Fender Dealer. 11. Instruments that have been serviced by unauthorized persons (any person other than a Fender Certified Technician at an Authorized Fender Service Center). THE FOREGOING CONSTITUTES THE ONLY WARRANTY MADE BY FENDER WITH RESPECT TO THE PRODUCTS AND IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED Any implied warranties, including without limitation, any implied warranties of merchantability or fitness for any particular purpose, imposed under state law are limited to the duration of this limited warranty . Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not be applicable to you. 31 Warranty FMIC ASSUMES NO LIABILITY FOR PROPERTY DAMAGE RESULTING FROM FAILURE OF THIS PRODUCT NOR ANY LOSS OF INCOME, SATISFACTION, OR DAMAGES ARISING FROM THE LOSS OF USE OF SAME DUE TO DEFECTS OR AVAILABILITY OF SAME DURING SERVICE. This warranty applies only to Fender instruments manufactured after January 1, 1998, and purchased and serviced within the U.S.A. and Canada. Warranties outside these countries are as defined by the authorized Fender Distributor for your country or region, and may vary from the above in terms and/or length. Fender Musical Instruments Corp. 8860 East Chaparral Road, Suite 100 Scottsdale, Ariz. 85250-2610 U.S.A. Phone: 480.596.9690 fender Fender®, Stratocaster®, Strat®, Telecaster®, Tele®, Precision Bass®, P Bass®, Jazz Bass®, J Bass® and the distinctive headstock designs commonly found on these guitars are registered trademarks of Fender Musical Instruments Corporation. All rights reserved. IMPORTADO POR: Instrumentos Musicales Fender S.A. de C.V., Calle Huerta # 132, Col. Carlos Pacheco, C.P. 228890, Ensenada, Baja California, Mexico. RFC: IMF870506R5A Hecho en Mexico. Servicio de Cliente: 001-8665045875 32 Warranty NOTICE REGARDING USE OF HISTORIC PATENT NUMBERS/MARKINGS: FENDER is proud to offer some of the most iconic musical instruments and amplifiers of the past 60 years. Some FENDER products are intentional recreations or reissues of vintage guitars and amplifiers, and may therefore incorporate markings or text associated with original patents that have since expired. Specific examples of such models include patent numbers on the tremolo plates and decals of the JAGUAR® and JAZZMASTER® guitars, “Pat Pending” on some vintage TELECASTER® guitar bridge plates, and “Design and Circuits Patented” language on the control panels of certain model amplifiers in FENDER V intage Modified, Vintage Reissue and Custom lines. Such markings are included only for the sake of historical accuracy , and are not intended to denote or imply live patents or ongoing patent protection. 33 34 P/N 0079381000 Rev. A © 2 MUSICAL INSTRUMENTS CORP.
Posted on: Mon, 08 Sep 2014 16:40:55 +0000
Trending Topics
Recently Viewed Topics
© 2015